- All
- Product Name
- Product Keyword
- Product Model
- Product Summary
- Product Description
- Multi Field Search
English  |
| Quantity: | |
|---|---|
TOPRISE FIRE PROOFING FRP ANTI-CORROSIVE SHEET
Corrosion resistance: Fire Proofing FRP Anti-Corrosive Sheet
Resin Ingredient: DIC 1060 reactive flame retardant resin
Surface Treatment: Surface applying Melinex 301 film.
Glass Fiber: Taishan high- quality glass fiber, the content no less than 28%.
Unit Weight: 2750g/m² 3050g/m² 3350g/m² 3685g/ m²
Nominal Thickness: 1.8mm 2.0mm 2.2mm 2.5mm
Heat Resistance Limit: -40℃ to +120℃
Light Transmittance: ＜1%
Anti- ultraviolet Rate: Adding more than 3.5‰ BASF UV absorbent
Warranty:15 years
Application：Inflammable and explosive workplaces, building roofs and walls with fireproof requirements
Note. Caustic Alkali: Na, K kind of Hydroxide Mixed Alkali: CO32 Water has stronger impact on FRP sheet than light, oxygen and heat. DIC 1060 reactive flame retardant resin 23
FRP SHEET INSTALLATION MUST PAY ATTENTION TO FOLLOWING
The waves of both sides of FRP should be lapped over color steel board.
A long waterproofing sticky belt should be installed on the outer side of longitudinal lapping waves or wave crest.
For crosswise lapping, lapping length is not less than 200mm. And waterproofing sticky belt should be installed on two ends of lapping parts respectively.
After setting fixing nails into waterproofing cushion ring, you may drive nails into purline or fix support.
Suggest applying copper silicon glue on nail driving place.
Suggest setting up U buckling strip if FRP assumes angle shape
Final Period during Installation
1. No crack and damage has occurred from fixing screw bolt or rivet.
2. No damage has occurred from dropped heavy articles.
3. No damage has occurred from accidental foot traffic.
4. There’s no gap left at side or end laps of the FRP sheet.
5. Remove all rarity from FRP sheet.
6. Made essential installation record as required by Building Regulation
Special Waterproofing Occasions:
In some places, if rainwater accumulates on the roof surface, it may drip through the plate under strong wind power and seep in waterproofing flashing. Under such circumstance, special measures must be taken in time.
It’s impossible that FRP sheet is processed into complicated curling shape to carry on lapping like color steel plate. Therefore, side waterproofing should be done with silicon glue or double wave crest lapping should be adopted. The following occasions probably lead to side water leakage.
Under strong wind, if FRP sheet on low wave crest fractures, we advise you use waterproofing core plug to seal.
On the high spot of roofing, particularly on the terminal of the roof where there are such peaks as rails and parapet，rainwater may accumulate in such places and overflow onto the rib of FRP sheet.
For great span installation, when roofing withstands frequent vibration, the rainwater might deposit. In such case, double wave crest lapping, special side waterproofing cover plate or silicon glue for waterproofing should be taken into consideration.
* Good No cracking phenomenon when driving nails in roof installation
* Having close combining with color steel plate. Cross- section thickness is uniform. The shape of FRP sheet is consistent with steel plate.
* Transmittance loss rate is low. No yellowing phenomenon after long term service.
* Thermal expansion coefficient is close to that of steel plate. No cracking and water leakage in nail driving place because of expand with heat and contract with cold.
* Light through FRP sheet assumes scattering shape and gentle.
* Bright and clean appearance, no distinct air bubble and cracking on FRP sheet.
* Anti- ultraviolet and anti- chemistry corrosion.
* Anti- ageing and anti- pulverization.
* Long service life.
Q: Could you customize the size?
A: We have standard thickness. We can customize the width, color and length. The length shall be less than the container length.
We need you to send roof profile drawing to us.
Q: What's your MOQ?
A: 500 meters.
Q: Could you recommend the model and quantity?
A: Yes, we can design the model and quantity as per the warehouse dimension and warehouse type.
Q:How about the lead time?
A: Normally 2 weeks. It depends on the quantity and our production plan.
TOPRISE FIRE PROOFING FRP ANTI-CORROSIVE SHEET
Corrosion resistance: Fire Proofing FRP Anti-Corrosive Sheet
Resin Ingredient: DIC 1060 reactive flame retardant resin
Surface Treatment: Surface applying Melinex 301 film.
Glass Fiber: Taishan high- quality glass fiber, the content no less than 28%.
Unit Weight: 2750g/m² 3050g/m² 3350g/m² 3685g/ m²
Nominal Thickness: 1.8mm 2.0mm 2.2mm 2.5mm
Heat Resistance Limit: -40℃ to +120℃
Light Transmittance: ＜1%
Anti- ultraviolet Rate: Adding more than 3.5‰ BASF UV absorbent
Warranty:15 years
Application：Inflammable and explosive workplaces, building roofs and walls with fireproof requirements
Note. Caustic Alkali: Na, K kind of Hydroxide Mixed Alkali: CO32 Water has stronger impact on FRP sheet than light, oxygen and heat. DIC 1060 reactive flame retardant resin 23
FRP SHEET INSTALLATION MUST PAY ATTENTION TO FOLLOWING
The waves of both sides of FRP should be lapped over color steel board.
A long waterproofing sticky belt should be installed on the outer side of longitudinal lapping waves or wave crest.
For crosswise lapping, lapping length is not less than 200mm. And waterproofing sticky belt should be installed on two ends of lapping parts respectively.
After setting fixing nails into waterproofing cushion ring, you may drive nails into purline or fix support.
Suggest applying copper silicon glue on nail driving place.
Suggest setting up U buckling strip if FRP assumes angle shape
Final Period during Installation
1. No crack and damage has occurred from fixing screw bolt or rivet.
2. No damage has occurred from dropped heavy articles.
3. No damage has occurred from accidental foot traffic.
4. There’s no gap left at side or end laps of the FRP sheet.
5. Remove all rarity from FRP sheet.
6. Made essential installation record as required by Building Regulation
Special Waterproofing Occasions:
In some places, if rainwater accumulates on the roof surface, it may drip through the plate under strong wind power and seep in waterproofing flashing. Under such circumstance, special measures must be taken in time.
It’s impossible that FRP sheet is processed into complicated curling shape to carry on lapping like color steel plate. Therefore, side waterproofing should be done with silicon glue or double wave crest lapping should be adopted. The following occasions probably lead to side water leakage.
Under strong wind, if FRP sheet on low wave crest fractures, we advise you use waterproofing core plug to seal.
On the high spot of roofing, particularly on the terminal of the roof where there are such peaks as rails and parapet，rainwater may accumulate in such places and overflow onto the rib of FRP sheet.
For great span installation, when roofing withstands frequent vibration, the rainwater might deposit. In such case, double wave crest lapping, special side waterproofing cover plate or silicon glue for waterproofing should be taken into consideration.
* Good No cracking phenomenon when driving nails in roof installation
* Having close combining with color steel plate. Cross- section thickness is uniform. The shape of FRP sheet is consistent with steel plate.
* Transmittance loss rate is low. No yellowing phenomenon after long term service.
* Thermal expansion coefficient is close to that of steel plate. No cracking and water leakage in nail driving place because of expand with heat and contract with cold.
* Light through FRP sheet assumes scattering shape and gentle.
* Bright and clean appearance, no distinct air bubble and cracking on FRP sheet.
* Anti- ultraviolet and anti- chemistry corrosion.
* Anti- ageing and anti- pulverization.
* Long service life.
Q: Could you customize the size?
A: We have standard thickness. We can customize the width, color and length. The length shall be less than the container length.
We need you to send roof profile drawing to us.
Q: What's your MOQ?
A: 500 meters.
Q: Could you recommend the model and quantity?
A: Yes, we can design the model and quantity as per the warehouse dimension and warehouse type.
Q:How about the lead time?
A: Normally 2 weeks. It depends on the quantity and our production plan.
